 FS: 1970 Roller $750 OBO |
|
|
|
Porsche, and the Porsche crest are registered trademarks of Dr. Ing. h.c. F. Porsche AG.
This site is not affiliated with Porsche in any way. Its only purpose is to provide an online forum for car enthusiasts. All other trademarks are property of their respective owners. |
|
|
  |
| didenpx |
 Jul 15 2025, 05:30 PM
Post
#1
|
|
Member  Group: Members Posts: 57 Joined: 1-September 23 From: Usa Member No.: 27,556 Region Association: North East States 
 |
For sale is a 1970 roller with cut fenders and stripped; I bought it in a lot and don't have any use for it. It was stored inside until last fall, was out in the elements with poor tarp coverage over the winter, and I have it under a car cover to save it until adoption.
It's a very solid shell with little rust except the jack points in the longs. The floors are solid, the longs forward of the jack points and underneath to the floor pan are are solid, the trunk and frunk floors are solid, the nose panel is solid, the corners of the tub in the front wheel well are solid, the rear firewall is solid. The hell hole will need some attention; the battery tray is non existent and there are two quarter sized hole beneath them on the top of the long but the jacking point underneath is solid and the bottom of the long looks good. It's too solid to scrap but I want it gone before the snow falls. I'm hoping someone will save it as the basis for a track car etc. If you have a parts donor car with rust issues but good quarters this could be a great basis to build on. I have it listed locally on Craigslist and have dozens of additional detailed photos of all of the typical rust areas that I'm familiar with (which are solid on this shell). It comes on a set of later star wheels; the Fuchs in the picture are NOT included and are listed for sale separately. Asking $750.00 or best offer. Located near Nashua NH.    Attached thumbnail(s) 
|
   |
 
|
| didenpx |
Jul 16 2025, 06:23 AM
Post
#2
|
|
Member Group: Members Posts: 57 Joined: 1-September 23 From: Usa Member No.: 27,556 Region Association: North East States
|
   |
|
|
|
| didenpx |
Jul 21 2025, 05:13 PM
Post
#3
|
|
Member Group: Members Posts: 57 Joined: 1-September 23 From: Usa Member No.: 27,556 Region Association: North East States
|
If it helps, I would be willing to haul a reasonable distance from Nashua NH for asking price plus cost of Uhaul trailer and gas. If it doesnt find a buyer before November I will reluctantly have to send it to the crusher.
|
|
|
|
| fiacra |
Jul 21 2025, 05:23 PM
Post
#4
|
|
Person.Woman.Man.Camera.TV Group: Members Posts: 583 Joined: 1-March 19 From: East Bay Region - California Member No.: 22,920 Region Association: Northern California
|
QUOTE(didenpx @ Jul 21 2025, 04:13 PM)  If it helps, I would be willing to haul a reasonable distance from Nashua NH for asking price plus cost of Uhaul trailer and gas. If it doesnt find a buyer before November I will reluctantly have to send it to the crusher. If nothing else, at least save that early rear bumper. Somebody will want that, even in its current state. |
 |
|
| didenpx |
Jul 21 2025, 06:34 PM
Post
#5
|
|
Member Group: Members Posts: 57 Joined: 1-September 23 From: Usa Member No.: 27,556 Region Association: North East States
|
Thanks @fiacra I had no idea they are desirable. I will make sure it gets saved if worst comes to worst.
|
|
|
|
| nolift914 |
Jul 28 2025, 07:16 AM
Post
#6
|
|
Autoxer Group: Members Posts: 186 Joined: 24-May 09 From: Rockaway Beach NY Member No.: 10,399 Region Association: None |
pm sent
|
|
|
|
| didenpx |
Jul 28 2025, 10:54 AM
Post
#7
|
|
Member Group: Members Posts: 57 Joined: 1-September 23 From: Usa Member No.: 27,556 Region Association: North East States
|
@nolift914 replied
|
|
|
|
|
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
|
Lo-Fi Version | Time is now: 30th July 2025 - 03:08 PM |
Invision Power Board
v9.1.4 © 2025 IPS, Inc.